EAA Builders Log Website
EMail address:
Password:
- Lost my password
close
EAA Builders Log
(An EAA website).
Help
Contact Us
About
Sign Up
Login
Project:
DaveBellairs
-
Listing of Entries
(Please mouse-over any icon to get a description of that function).
Categories
Show All Entries
- (652)
Research
Workshop
- (4)
Empennage
- (14)
Fuselage
- (54)
Firewall
- (78)
Tail Feathers
- (40)
Wings
- (105)
Controls
- (6)
Avionics
- (149)
Lighting
- (13)
Instrument Panel
- (9)
Landing Gear
- (4)
Engine
- (159)
-
Prop oil line grommet
-
Heat shield
-
Installed new heat muff
-
New heat muff
-
Heat muff
-
Ordered new heat muff
-
More wire routing to...
-
Backup Alternator...
-
More wire runs
-
Alternator wires and...
-
Power cable pass...
-
Stater cable wrap...
-
MAP line and starter...
-
Forward engine...
-
Secondary control...
-
Oil temp cable
-
Secured Control cables
-
Throttle cable
-
Prop governor cable...
-
Prop gov rod end...
-
More throttle cable...
-
New firewall pass...
-
Firewall pass throughs
-
ElectroAir spark...
-
Coil pack relocated
-
Upper cowl
-
Upper cowl and oil door
-
Lower cowling
-
Lower cowl primed
-
Oil dipstick
-
Coil pack reposition
-
Wingtip lens
-
Cowl hinge pin stop
-
Oil door hinge paint
-
Alternator bolts
-
Spark plug wires
-
Engine plumbing
-
Left side engine...
-
Engine probe and...
-
Man pressure line
-
Oil door primed, oil...
-
Oil door
-
Scat tube and CHT...
-
cabin heat scat tube
-
ElectroAir EIS...
-
Red cube wires
-
Right inlet diffuser...
-
Cowling pin hole...
-
ElectroAir spark plugs
-
ElectroAir spark plugs
-
Lower cowl sanding
-
Fluid hoses
-
Bonaco fluid lines
-
Alternator lock plate
-
Map sensor plumbing
-
ElectroAir MAP sensor
-
Manifold pressure line
-
Park brake valve...
-
Top cowl sanding and...
-
Bonaco Brake lines
-
Top cowling and...
-
Coil pack install
-
EGT probes, oil and...
-
EGT probes
-
Engine probes
-
Backup Alternator
-
Alternate air door...
-
Baffles
-
ElectroAir install
-
ElectroAir coil pack...
-
Baffle rods and more...
-
Baffles, inlet...
-
Final baffle install
-
Front Cowling...
-
Adel clamps and oil...
-
Oil cooler line...
-
Front Skybolt...
-
Diffuser paint and...
-
Top Dead Center
-
Finding TDC on #1...
-
Fuel injector servo...
-
Left side baffle...
-
Baffle spark plug...
-
Spark plug baffle...
-
Oil cooler installed...
-
Oil cooler duct
-
Oil cooler sealing...
-
Oil cooler...
-
Plenum paint prep
-
Baffle tension rods
-
AC specialties...
-
Red cube...
-
Top cowling paint...
-
Clogged rattle can...
-
Inlet diffusers and...
-
Cowling heat shield,...
-
Cowling heat shield...
-
Painting inlet...
-
Engine breather tube
-
Engine mount bolts,...
-
New magneto gear
-
Interior cowl hinge pin
-
Oil cooler finished
-
Cowl side hinge pins
-
Oil cooler duct
-
Cowl sanding, baffle...
-
Oil cooler mounts
-
Baffle tie rods
-
Oil cooler mount
-
Cowling hinge pins...
-
Nut plate Electro...
-
Cowling tabs
-
Cowling tabs
-
Neoprene sleeves and...
-
Oil collar duct and...
-
Oil cooler duct...
-
Neoprene sleeves and...
-
Inlet neoprene
-
Front cowling fasteners
-
Nut plates on plenum...
-
Plenum mod voids and...
-
Plenum mod results
-
Plenum mod
-
Plenum corner mod
-
Plenum, transit duct...
-
Plenum and transit...
-
Plenum mod and...
-
Plenum extension and...
-
Plenum extension
-
Oil cooler mount
-
Trimmed plenum
-
Oil cooler mount...
-
Sanded cowl
-
Cowling hinges
-
Cowl hinges and...
-
Pro seal cowl hinges
-
Cowling hinges
-
Inlet repair
-
More nut plate backers
-
Baffle cooling mod...
-
Right rear baffle mod
-
Plenum nut plates
-
Plenum nut plates
-
More nut plates
-
Nut plates
-
Inlet diffuser nut...
-
Baffle and inlet nut...
-
More inlet diffuser...
-
Plenum nut plates
-
Front baffles
-
Left inlet baffle
-
Fabbing baffle angles
-
Plenum trimming fwd...
-
Front center baffles...
-
Baffle trimming and...
-
Plenum
-
Left center baffle...
-
Left plenum and...
-
Hung the engine
Propeller
- (1)
Fuel System
- (7)
Interior Finish
- (3)
Paint / Decals
- (6)
Inspection
Tools
Builder Name:
Dave Bellairs
-
Project:
Vans - RV-7
-
VIEW REPORTS
Total Hours:
1460.9
Total Flight Time:
Start/Last Date:
Jun 24, 2017 - No Finish Date
Engine:
Lycoming IO-360
Propeller:
Whirlwind 200RV
Panel:
Advanced Flight Systems Avionics
Friendly URL:
https://eaabuilderslog.org?s=DaveBellairs
Home or Last Project Picture
Jun 24, 2021
Nut plate Electro Air MTH and cowl pins
- (3 hours)
Category: Engine
Installed nut plates on cowling tabs. Received my Electroair ignition kit and temp installed MTH in right mag port. Drilled the firewall for rear inserted cowling hinge pins. Need to improve ease of installation of pins. Lots of friction.
E231593F-FFC8-40F7-91E7-1A1082569DE8.jpeg
F1B0DCB5-07FD-49B0-B5C9-23156F523AA0.jpeg
B09D3ABE-18D3-4E0B-BD33-AC990F871B4D.jpeg
NOTE: This information is strictly used for the EAA Builders Log project within the
EAA organization
.
-
Policy
-
© Copyright 2024 Brevard Web Pro, Inc.